premise of design requirements, adding external sunshade , awning and appropriately

Wencheng County high-end dual-mode ultrasonic welding machine / motor lift [Today / Information] 2022 has been updated such as: speakers, dashboards, folders, lamps, vacuum cleaners, filters, electric mosquito pats, etc. Double-head ultrasonic plastic welding machine, can give full play to its welding effect when welding hard plastic materials, ultrasonic welding machine, special scope: used for car body plastic parts, car doors, car instruments, headlamps, mirrors, sunshades, interior decoration, filters, plastic electronic products: prepaid water meters, electricity meters, communication equipment, cordless phones, mobile phone accessories.

Moreover, the hot weather will cause damage not only to the paint surface, but also to the car interior and dashboard. Therefore, car owners are advised to install sunshade curtains on their cars in summer. Has a very good thermal insulation effect, effectively isolate the sun, ultraviolet rays, but also can block the light and protect privacy.

Windows also have heat preservation, heat insulation, sunshade, anti-wind and rain, noise and other functions. From the analysis of the composition of building energy consumption, it is found that the energy loss through doors and windows is very serious, which is the main reason that affects the building thermal environment and causes excessive energy consumption.

Vehicle windshield sunshade cloth, also known as car sunshade, it can reduce the temperature in the car to a certain extent, protect the instrument and seat equipment in the car, and play a certain role. The material of sunshade is basically made of aluminum foil and multi-layer bubble film, which has good strength, toughness and impact resistance. Aluminum foil has the ability to reflect light, thus reducing thermal radiation and has low thermal radiation conductivity.

Experts say that water shading should be used in the south and north directions of buildings; vertical shading should be used in northeast, north and northwest directions; comprehensive shading should be used in southeast and southwest directions; and baffle shading should be adopted in east and west directions. In architectural design, it is appropriate to combine exterior corridors, balconies and eaves to achieve sunshade in hot summer and warm winter areas, with long summer heat and strong solar radiation

The 13th Guangzhou sunshade door and window Exhibition, sponsored by Guangzhou Slogart Exhibition Planning Co., Ltd., will be solemnly opened in Guangzhou International Purchasing Center from July 8 to 10, 2023. With the theme of “Intelligent Technology, Green Building, Energy Saving and Environmental Protection”, this exhibition strives to create a building materials industry exhibition platform for domestic customers and traders. As the weather vane of the industry, this platform provides the best purchasing platform for dealers, real estate developers, engineers, even designers, decoration market, building materials market, door and window market, building materials supermarket and so on. It also provides enterprises with the best opportunity to show new products, expand the market, build channels and promote brands.

In the past, for example, if the car was parked outside in summer, the temperature inside the car with closed windows would rise sharply to 50 or 60 degrees Celsius or even higher under the exposure of the sun, and the high temperature would damage the dashboard and the real p seat. Because the windows of many cars are covered with solar film, the front and rear windshield has become the main way for the sun to enter. The easy-to-fold windshield, which reflects most of the sunlight, is usually made of tin foil and is especially effective when parked for a short time. Curtains or car windows should also be affixed or installed with sunshade curtains, the installation of car curtains only install a chute on the top and bottom of the window, and then install the curtains in the meantime, but sometimes the chute will not be smooth, it is more troublesome to pull up at this time.

Under the premise of design requirements, adding external sunshade, awning and appropriately increasing the length of southward balcony can play a certain sunshade effect. Heat-reflecting fabric curtains coated with metal film are arranged on the inside of the window, which has a decorative effect on the front, forming a less mobile space layer about 50mm thick between the glass and the curtains. In this way, a good effect of thermal reflection and thermal insulation can be achieved, but the direct lighting is poor and should be made into a movable type. In addition, the inside of the window with a certain heat reflection doors and windows to seek a balance between function and aesthetics, exquisite and chic modeling, the pursuit of high-quality attitude towards life, quality products, intimate design, only to bring you a different life.

Hand sweat wear resistance instrument can simulate automobile interior products, including: dashboard, touch screen, door interior panel, steering wheel, seat, roof, floor mat, sunshade, storage box, ashtray and other interior materials, as well as mobile phone glass screen and shell and other finger / skin wear process. At the same time, the system can also be tested in liquid environment, such as artificial sweat, emulsion and so on. By changing different fixtures, the system can simulate all kinds of wear processes: finger wear, nail scratches, sole wear, industrial scratches and fingerprint cleaning.

The sunscreen of the car should use one side of the aluminum foil to face the sun. The sunshade is aluminum foil film on one side and cartoon pattern on the other. The color silver-coated reflective layer reflects 100% sunlight, effectively isolates the heat conduction, greatly reduces the temperature inside the car and reflects ultraviolet rays, thus protecting the objects in the car. On a hot summer day, some items in the car, such as perfume holders, lighters, cans and so on,

More installation method has a double-sided detachable, double-sided detachable installation node, which is a good node for bracket installation. At present, the maintenance of ultra-polymer photovoltaic support bearings is developing rapidly. If there is no such use of pressure and mechanical fixation, it is likely to produce a lot of defects. Such as irregular axial loosening, axial pressure deformation, installation collision, photovoltaic support instability and so on. Erguna connected greenhouse tube structure of a variety of assembly plants can use these pipes, electrical equipment to form a workspace, does not require a large amount of investment. This automatic device mainly relies on the computer as the control center to control the facilities such as skylight, sunshade, heat preservation, wet curtain / fan cooling, spray drip irrigation or drip irrigation, seedbed and so on. Of course, the automatic device can not only rely on the control of the computer, it also has acquisition and control.